PG 600 WHITE FLEXI ADHESIVE FOR FIXING TILES, MARBLE AND NATURAL STONE
Check Availability
Original price was: ₹1,300.00.₹1,060.00Current price is: ₹1,060.00.
Bulk Order →
BRAND: –
- AGL – POWER GRACE BONDING SOLUTIONS
AREA OF APPLICATION
Suitable for fixing tiles of apparent porosity less than or equal to 3% On indoor and outdoor areas Suitable for over-tiling indoor applications on old tiles, without primer Suitable for applications where high performance is required, i.e. pools, industrial areas, facades on walls and floors
COVERAGE
20kg bag at 6mm thickness, may vary upon notch trowel size at site condition.
Product Description
- DESCRIPTION
- 1. PG-600, is a one-pack premixed adhesive consisting from high quality cements, selected silica/quartz sands and specific additives with a high polymer content. It is suitable for laying marble and natural stone for interior and exterior application
- 2. PG-W600, is a white cementitious polymer modified tile adhesive for interior and exterior installation of glass tiles, natural stone, composite marble stone etc. It is suitable for laying in swimming pools or high traffic areas.
- Note: PG-600 & W600 are ready to use flexi adhesive, also confirms to EN C2TE (TE, T = thixotropic / high sag resistance & E = extended open time)
BENEFITS
- No vertical slipping Extended open time Frost proof One-pack Can be applied up to 10 mm thickness Can be applied on cement waterproofing mortars Needs no curing & soaking of tiles.
SURFACE PREPARATION
- Surface should be sound and clean, free from dust, grease, oil, loose material, paint etc. Movement joints to be filled with suitable joint filler. The surface must be in SSD condition before application.
APPLICATION INFORMATION MIXING
- Mix 20kg bag of PG-600 & W600 in Approx. 6.5l to 6.75l of clean water and mix thoroughly until a slump free mortar is achieved. Mix with a trowel or slow speed drills for homogeneous mix. Allow it to slake for 5 minutes. Mix the required quantity, which can be used within the desired pot life, not exceeding 1m² area.
APPLICATION
- Spread the adhesive uniformly on the surface as required with proper notch trowel to get the required depth of 6-12mm. Place the tile on the adhesive surface and press firmly into position with a slight twisting action, ensure that good contact is maintained to the back of each tile, eliminating the possibility of any air voids. Tiles should be applied within 15 to 20 minutes of adhesive being applied. Keep adequate joints between two tiles using spacers. Clean off surplus adhesive from the tile face and between joints.
PRECAUTIONS
- Always add powder to water and never add water to powder. Never add excess water than recommended. Surface should be hard and in sound condition for floor tiling. Do not use in damp Conditions. Not recommended for tiling on paint, wood, metal and gypsum.
More Products From This Vendor
WARDROBE DRAWER – WARDROBE SYSTEM (TUDOOR)
Original price was: ₹15,591.00.₹10,914.00Current price is: ₹10,914.00.
Saffron Gold, Rose Gold And Matt Black Basin Tap
Original price was: ₹9,500.00.₹5,700.00Current price is: ₹5,700.00.
TABLE TOP WASH BASIN – SANITY (SIFON)
₹2,027.00 – ₹2,275.00
2 Way Switch – 20AMP. SWITCHES 240V (1 MODULE) – RIDGE (NORWOOD)
Original price was: ₹46.00.₹42.00Current price is: ₹42.00.
Ski-Fi LIGHT DIMMER (2M) (NORWOOD)
Original price was: ₹6,248.00.₹4,062.00Current price is: ₹4,062.00.
Reviews
There are no reviews yet.